Volvo Penta D16 Operator'S Manual Download

Page: 77 / 90

Replacing Battery

IMPORTANT:

Make sure that the new battery fulfills the specifications
in

Technical Data

. Read the information supplied with

the battery before you begin the installation.

IMPORTANT:

Do not disconnect the batteries with the engine
running.
Sensitive electrical components can be immediately
damaged.

WARNING!

Never confuse the positive and negative poles on the
batteries. Risk of arcing and explosion.

Disconnecting (A)

1 Untighten the nut and remove the – cable (black).

2 Untighten the nut and remove the + cable (red).

Remove the battery.

Connecting (B)

Place the new battery.

1 Connect the + cable (red) to the + pole on the

battery and tighten the nut.

2 Connect the – cable (black) to the – pole on the

battery and tighten the nut.

NOTICE!

Hand in the old battery to a re-cycling station.

Maintenance

47711740 05-2019 © AB VOLVO PENTA

Summary of Contents for D16



























































































Search results

Summary of Contents for D16

Reviews:

Related manuals for D16

Brands by name

Popular brands

Volvo Penta D16, Operator'S Manual

Search results

Summary of Contents for D16

Reviews:

Related manuals for D16

Brands by name

Popular brands