Volvo Penta D16 Operator'S Manual Download | Manualshive

Page: 73 / 90

background image

Impeller, Check and Change

WARNING!

Risk of water entry. Close the seawater cocks before
doing any work on the seawater system.

1 Remove the seawater pump lid, and pull the

impeller out with universal impeller puller.

2 Check the impeller. If any cracks or other defects

are visible, the impeller must be changed.

3 Lubricate the pump housing and the inside of the

lid with water-resistant grease (which is not
aggressive to rubber). The impeller will be easier to
work with if it is put in hot water prior to fitting.

4 Press the impeller in with a circular motion (counter

clockwise). The shaft of the pump has an internal
thread (M8). Screw a stud into the end of the shaft
and press the impeller in using a washer and nut.
Fit the cover, using a new O-ring.

5 Open the sea cock.

NOTICE!

Always carry a spare impeller on board.

Maintenance

47711740 05-2019 © AB VOLVO PENTA

71

«
...
71
72
73
74
75
...
»

Summary of Contents for D16



























































































Reviews:

No comments

Related manuals for D16

Brand: Westerbeke Pages: 60

Brand: Rato Pages: 32

Brand: Briggs & Stratton Pages: 20

LYCOMING 200-6XL Series

Brand: E-MAG Pages: 30

Brand: Bosch Pages: 20

Rexroth Hagglunds CA 10

Brand: Bosch Pages: 53

Brand: Bosch Pages: 60

Brand: Bosch Pages: 74

Rexroth Hagglunds CA 100

Brand: Bosch Pages: 76

Rexroth 70 Series

Brand: Bosch Pages: 56

Rexroth IndraDyn T

Brand: Bosch Pages: 76

Rexroth A10VER 52 Series

Brand: Bosch Pages: 56

Brand: Bosch Pages: 48

Brand: Bosch Pages: 114

Brand: Bosch Pages: 72

Rexroth A6VM series 71

Brand: Bosch Pages: 76

Rexroth Hagglunds VI 44 Series

Brand: Bosch Pages: 68

Rexroth IndraDyn S MS2N

Brand: Bosch Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands