Volvo Penta 3.0GL-B Operator'S Manual Download

Page: 94 / 108

7741591 / 2003-12

Specifications

Engine . . . . . . . . . . . . . . . . . .

3.0GS-B, 3.0GS-C

Bore and stroke . . . . . . . . . . . . . . . . .

4.00 x 3.60 inches (101.60 x 91.44 mm)

Cylinders (number) . . . . . . . . . . . . . .

4 in-line

Displacement . . . . . . . . . . . . . . . . . .

3.0 liters (181 Cu. In.)

Firing order . . . . . . . . . . . . . . . . . . . .

1 – 3 – 4 – 2

Full throttle operating range . . . . . . .

4200 – 4600 RPM

Idle RPM (fixed) . . . . . . . . . . . . . . . .

650 – 750 RPM in forward gear

Fuel System

Carburetor . . . . . . . . . . . . . . . . . . . . .

Adjustable idle circuit, fixed main fuel jets, electric choke

Fuel Pump . . . . . . . . . . . . . . . . . . . . .

Mechanical

Fuel filter (in fuel pump) . . . . . . . . . .

Water separating 10 micron fuel filter, Volvo Penta Part no. 3855104

Fuel filter location . . . . . . . . . . . . . . .

Refer to photographs on Features pages.

Fuel type . . . . . . . . . . . . . . . . . . . . . .

Inside the U.S.: 89 octane (AKI) unleaded gasoline

Outside the U.S.: 93 octane (RON) unleaded gasoline

Electrical System

Charging system . . . . . . . . . . . . . . . .

12 volt 65 amp alternator, with internal transistorized voltage regulator

Battery size . . . . . . . . . . . . . . . . . . . .

12 volt with 360 Cold Cranking Amp (CCA) rating

Starter . . . . . . . . . . . . . . . . . . . . . . . .

12 volt 1.7kW output, planetary reduction gear

Ignition System

Distributor . . . . . . . . . . . . . . . . . . . . .

Delco EST

Ignition timing . . . . . . . . . . . . . . . . . .

2° ATDC, special tool Volvo Penta part no. 885163 required

Spark plugs . . . . . . . . . . . . . . . . . . . .

Volvo Penta Part no. 3854399

Spark plug gap . . . . . . . . . . . . . . . . .

0.045 inches (1.14 mm)

Spark plug installation torque . . . . . .

27 N•m (20 ft. lb.)

Cooling system

Raw water pump . . . . . . . . . . . . . . . .

Crankshaft mounted variable volume flexible impeller pump

Recirculating pump . . . . . . . . . . . . . .

Fixed impeller belt driven pump on engine

Thermostat . . . . . . . . . . . . . . . . . . . .

71°C (160°F) Volvo Penta part no. 3853799

Oil capacity

Engine without filter . . . . . . . . . . . . .

3.5 quarts (3.3 liters)

Engine with filter . . . . . . . . . . . . . . . .

4 quarts (3.8 liters)

Drive unit . . . . . . . . . . . . . . . . . . . . . .

Approximately 2.2 quarts (2.1 liters)

Oil filter . . . . . . . . . . . . . . . . . . . . . . .

Volvo Penta Part no. 835440

Oil filter location . . . . . . . . . . . . . . . .

Refer to photographs on features pages.

Oil type

Engine . . . . . . . . . . . . . . . . . . . . . . . .

DuraPlus™ Premium engine oil labeled for API service CE/SG

Drive unit . . . . . . . . . . . . . . . . . . . . . .

DuraPlus SAE 75W/90 API service GL 5 synthetic gear oil

Power steering fluid U.S. . . . . . . . . .

DuraPlus power steering fluid Part no. 3851039

Power steering fluid non-U.S. . . . . . .

ATF oil Dexron 2 Part no. 1161941

NOTE! Volvo Penta of the Americas, Inc., reserves the right to make changes in weight, construction, materials,

or specifications without notice or obligation.

7741591 - Downloaded from www.volvopenta.com 12/03/2014 09:32:39

Summary of Contents for 3.0GL-B













































































































Search results

Summary of Contents for 3.0GL-B

Reviews:

Related manuals for 3.0GL-B

Brands by name

Popular brands

Volvo Penta 3.0GL-B, Operator'S Manual

Search results

Summary of Contents for 3.0GL-B

Reviews:

Related manuals for 3.0GL-B

Brands by name

Popular brands