manualshive.com logo in svg

Volvo Penta 3.0GL-B, Operator'S Manual

Share
Download
Volvo Penta 3.0GL-B Operator'S Manual Download Page 17

15

7741591 / 2003-12

Your Volvo Penta product consists of two components: the engine and the drive. There are certain parts on each component that
you, the owner, must take care of to make sure that your Volvo Penta product stays in optimum running condition. The important
parts of each component are shown in the photographs on the following “

Features” pages. Explanations of these parts and sys-

tems are described below; the maintenance procedures are found in the 

Maintenance section.

 Features

Circuit breakers and fuses

4.3GL-A, 5.0GL-A, 5.0GL-B, 5.7GL-A, 5.7GL-B

4.3GXi-A, 5.0GXi-A, 5.7Gi-B/GXi-A

1 2

2

3

4

3.0GS-B, 3.0GS-C

4.3GXi-B(F), 5.0GXi-B(F), 5.7Gi-B(F),
5.7GXi-C(F), 8.1Gi-B(F), 8.1GXi-A(F),
DPX375-B(F), DPX420-B(F)

4

2

1

1.

40 Amp Harness Fuse

2.

Spare Fuse

3.

7.5 Amp Fuel Pump Fuse

4.

50 Amp Circuit Breaker Power Trim Pump

5.

15 Amp Ignition/Fuel Fuse

6.

20 Amp Fuel Pumps

7.

20 Amp Insturment Panel Accessory

8.

15 Amp Engine Control Module (ECM) Fuse

9.

15 Amp Spare Accessory Fuse

10. 20 Amp Spare Accessory Fuse

7

2

6

5

8

9

10

4

5

2

2

6

1

7741591 - Downloaded from www.volvopenta.com 12/03/2014 09:32:39

Summary of Contents for 3.0GL-B













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands