viZaar VUCAM AM+ Operating Instructions Manual Download Page 62

Page: 62 / 79

4 APPliCATion - UsER inTERFACE - DoCUMEnTATion

7. Select "network conﬁguration" using the arrow but-
tons and conﬁrm your selection by pressing

8. Make sure that the settings are set as follows:
"Streaming: active“, "Start streaming: on startup",
"Streaming type: unicast".

9. exit the menu and go back to the operation menu
by pressing

three times.

Your VucaM

+ is now ready for streaming. In order

to start the stream, follow the steps in this chapter:

4.7.5 sTART sTREAM, page 66

Your Pc/Laptop will now conﬁgure the IP address of
your Lan connection. exit the program by pressing
any key.

8. remove the Sd card from the Sd card slot of your
Pc/Laptop.

1. Insert the Sd card with the conﬁguration data
taken from your Pc/Laptop into the Sd card slot of
your VucaM

2. open the main menu of the VucaM

+ by pressing

3. Select "system settings" and conﬁrm your selection
by pressing

4. now select "conﬁguration data" using the arrow
buttons and conﬁrm your selection by pressing

5. In the following menu, you will ﬁnd a ﬁle named

"Custom_Netw_ﬁx-206.cfg"

. the ﬁle is already se-

lected. conﬁrm your selection by pressing

Your VucaM

+ will now reboot. after approximately

30 seconds, the network ﬁle is successfully loaded
and you will ﬁnd yourself again in the operation
menu.

6. open the setup and select "system settings". con-
ﬁrm your selection by pressing

4.7.3

PREPARing ThE vUCAM

Summary of Contents for VUCAM AM+
















































































Search results

Summary of Contents for VUCAM AM+

Reviews:

Related manuals for VUCAM AM+

Brands by name

Popular brands

viZaar VUCAM AM+, Operating Instructions Manual

Search results

Summary of Contents for VUCAM AM+

Reviews:

Related manuals for VUCAM AM+

Brands by name

Popular brands