Vivotek CC9380-HV User Manual Download

Page: 80 / 375

VIVOTEK

80 - User's Manual

► If the default ports are already used by other devices connected to the same router, the Network

Camera will select other ports for the Network Camera.

► If UPnP

is not supported by your router, you will see the following message:

Error: Router does not support UPnP port forwarding.

► Steps to enable the UPnP

user interface on your computer:

Note that you must log on to the computer as a system administrator to install the UPnP

components.

1. Go to Start, click

Control Panel

, then click

Add or Remove Programs

2. In the Add or Remove Programs dialog box, click

Add/Remove Windows Components

3. In the Windows Components Wizard dialog box, select

Networking Services

and click

Details

NOTE:

Summary of Contents for CC9380-HV
























































































































































































































































































































































































Search results

Summary of Contents for CC9380-HV

Reviews:

Related manuals for CC9380-HV

Brands by name

Popular brands

Vivotek CC9380-HV, User Manual

Search results

Summary of Contents for CC9380-HV

Reviews:

Related manuals for CC9380-HV

Brands by name

Popular brands