Vivotek CC9380-HV User Manual Download

Page: 6 / 375

VIVOTEK

6 - User's Manual

Hardware Installation

1. Jot down the camera's MAC address for later reference. This is especially important if

you install numerous cameras at an installation site.

Network Camera

Model No: XXXXXX
MAC: 0002D1083236

Pat. 6,930,709

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

Made in Taiwan

IMPORTANT:

Do not remove the protective sheet before the installation is completed.

Summary of Contents for CC9380-HV
























































































































































































































































































































































































Search results

Summary of Contents for CC9380-HV

Reviews:

Related manuals for CC9380-HV

Brands by name

Popular brands

Vivotek CC9380-HV, User Manual

Search results

Summary of Contents for CC9380-HV

Reviews:

Related manuals for CC9380-HV

Brands by name

Popular brands