Vivotek CC9380-HV User Manual Download

Page: 55 / 375

VIVOTEK

User's Manual - 55

■ Schedule mode

The Network Camera switches between day mode and night mode based on a specified

schedule. Enter the start and end time for day mode. Note that the time format is [hh:mm] and is

expressed in 24-hour clock time. By default, the start and end time of day mode are set to 07:00

and 18:00.

Sensitivity of IR cut filter

Tune the responsiveness of the IR filter to lighting conditions as Low, Normal, or High.

When completed with the settings on this page, click

Save

to enable the settings.

Summary of Contents for CC9380-HV
























































































































































































































































































































































































Search results

Summary of Contents for CC9380-HV

Reviews:

Related manuals for CC9380-HV

Brands by name

Popular brands

Vivotek CC9380-HV, User Manual

Search results

Summary of Contents for CC9380-HV

Reviews:

Related manuals for CC9380-HV

Brands by name

Popular brands