Vivotek CC9380-HV User Manual Download

Page: 18 / 375

VIVOTEK

18 - User's Manual

LED Definitions

Item LED status

Description

LED De`finitions

Steady

Red

Powered and system booting, or network failed

Red

LED off

Power off

Green

LED off

Network is disconnected

Steady

Red

and

Green

LED blinks every 1

sec.

Connected to network

Green

LED blinks every 1 sec. and

RED

LED

blinks consecutively every 0.15 sec.

Upgrading firmware

Green

and

RED

blink

every 0.15 sec,

Green

and

RED

light on, then

blink again.

Restoring defaults

RED

LED is on,

Green

LED blinks and

RED

LED is constantly on.

Status after a reset (network connected)

Green

and

RED

LEDs are constantly on.

Status after a reset (network disconnected)

Hardware Reset

The reset button is used to reset the system or restore the factory default settings.

Sometimes resetting the system can return the camera to normal operation. If the system

problems remain after reset, restore the factory settings and install again.

Reset: Press the recessed reset button. Wait for the Network Camera to reboot.

Restore: Press and hold the reset button until the status LED rapidly blinks. Note that all

settings will be restored to factory default. Upon successful restore, the status LED will

blink green and red during normal operation.

SD/SDHC/SDXC Card Capacity

This network camera is compliant with

SD/SDHC/SDXC 16GB / 8GB / 32GB / 64GB

and

other preceding standard SD cards.

Summary of Contents for CC9380-HV
























































































































































































































































































































































































Search results

Summary of Contents for CC9380-HV

Reviews:

Related manuals for CC9380-HV

Brands by name

Popular brands

Vivotek CC9380-HV, User Manual

Search results

Summary of Contents for CC9380-HV

Reviews:

Related manuals for CC9380-HV

Brands by name

Popular brands