Vivotek CC9380-HV User Manual Download

Page: 106 / 375

VIVOTEK

106 - User's Manual

11. When the certifice file is successfully loaded, its status will be stated as

Active

Note that

a certificate must have been created and installed before you can click on the “

Save

button for the configuration to take effect.

12.To begin an encrypted HTTPS session, click

Home

to return to the main page. Change the URL

address from “

http://

” to “

https://

“ in the address bar and press

Enter

on your keyboard. Some

Security Alert dialogs will pop up. Click

Yes

to enable HTTPS.

Summary of Contents for CC9380-HV
























































































































































































































































































































































































Search results

Summary of Contents for CC9380-HV

Reviews:

Related manuals for CC9380-HV

Brands by name

Popular brands

Vivotek CC9380-HV, User Manual

Search results

Summary of Contents for CC9380-HV

Reviews:

Related manuals for CC9380-HV

Brands by name

Popular brands