Virutex FR129N, Operating Instructions Manual, Page: 12 / 52

12
Loosen levers S (Fig. 16). Place the machine (Fig. 16)
over the rebate of the frame turning the indicator to
“MARCO DERECHO” (RIGHT-HAND FRAME) or “MARCO
IZQUIERDO” (LEFT-HAND FRAME), depending on the
opening of the door, towards its upper part.
Tighten the clamp vises over the thickness of the door
using crank handles F (Fig. 16).
Move base 2 (Fig. 16) along the width of the rebate,
until it aligns with interior face T (Fig. 16). Secure the
machine in this position using levers S (Fig. 16).
Ensure that the machine is not connected to the mains.
Place the cutter bit touching the edge of the frame at
cutting edge Q (Fig. 15). Using knob U (Fig. 16), lock it
into this position at distance X (Fig. 16) from fixed stop
B2 (Fig. 16), equivalent to the width of the recess desired.
The width limit will thus be adjusted.
POSITIONING THE MACHINE FOR MAKING RECESSES,
ADJUSTING THE DEPTH OF RECESS AND MOUNTING THE
DISTRIBUTOR TUBE is done just as if one was working with
a template, as explained in sections 7 and 8 of this manual.
When MAKING RECESSES, instead of moving the motor
body along the inside of the template, move it between the
lengthways and sideways stops dealt with in this section.
11. PLACING HINGES LEVEL WITH THE EXIT
FACE, OR IN FRAMES WITHOUT REBATE, WITH
OR WITHOUT TEMPLATE
To place hinges in frames without rebates, or in frames
with rebates larger than the template that is available
and/or in those where one wants the door to fit flush
with the frame on the exit face, the machine has two
adjustable stops C1 (Fig. 17 and 18), which enable the
machine to be positioned in the frame on the external
face of it (Fig. 17) and on the door on the exit side of it
(Fig. 18), instead of positioning it by the frame rebate
and the entry face of the door, as in the standard process
which has been explained.
The process for making the recesses is identical to that
explained in sections 7 and 8 of this manual except with
regard to the MACHINE POSITION FOR THE FIRST RECESS:
where in the frame, instead of moving the base of the
machine 2 (Fig. 17) along the width of the rebate until
it stops with the interior face of it, the position of the
hinge has to be adjusted with respect to the frame with
screws C1 (Fig. 17). Secure them with bolts D1 (Fig. 17),
and secure the base in this position with levers S (Fig. 17).
Once adjusted for the frame, adjustable stops C1 (Fig.
17 and 18) can also be used to position the machine
in the door, but, unlike the standard process (Fig. 18),
using the exit face
12. RECOMMENDATIONS
Use the corresponding templates for the shapes and
dimensions of the hinges to be fitted.
Use adequate cutter bits and template guides corres-
ponding to the cutter bit diameter.
13. MAINTENANCE
13.1 BRUSHES AND COLLECTOR
Unplug the machine from the mains
before carrying out any maintenance
operations.
Remove the screws E1 (Fig. 19) that hold the side covers
G1 and detach them.
Remove the brush-holder J1 (Fig. 20) with small screwdriver
K1, using one of the brush-holder side tabs to lever it out.
Push back the end of spring F1. Keep it in this position
to extract the brush and replace it with a new genuine
VIRUTEX brush. Reinsert the brush-holder, ensuring
that it is firmly positioned in the casing and that each
of the brushes exerts a small amount of pressure on
the collector.
Re-attach the covers G1 with the corresponding screws,
making sure that no wires get caught in the process.
It is advisable to leave the machine running for 15
minutes once the brushes have been changed.
If the collector burns or juts out, it should be serviced
by a VIRUTEX service technician.
To ensure that mobile parts continue to move correctly,
remember to get rid of any dirt, dust and shavings
produced when making recesses.
Keep the cable and plug in good service condition.
14. ACCESSORIES
Standard templates for different hinges
Template guides for different cutter bit diameters.
2945471 90º CORNER CHISEL RC29M
15. TEMPLATE GUIDES AND CORRESPONDING
CUTTER BITS
See (Fig. 21).
16. NOISE LEVEL
The noise and vibration levels of this device have
been measured in accordance with European stan-
dard EN60745-2-17 and EN 60745-1 and serve as a
basis for comparison with other machines with similar
applications.
The indicated vibration level has been determined for
the device’s main applications and may be used as an
initial value for evaluating the risk presented by expo-
sure to vibrations. However, vibrations may reach levels
that are quite different from the declared value under
other application conditions, with other tools or with
insufficient maintenance of the electrical device or its
accessories, reaching a much higher value as a result