Viessmann SCU224 User Manual Download Page 45 | Manualshive

Page: 45 / 52

Viessmann SCU224 User Manual Download Page 45

©

Viessmann

5443203

45

|

SCU224

Time period - switch-on conditions
tDTO

:

Time period -
switch-on conditions
Adjustment range: 1 ... 100 s
in steps of 1 s
Factory setting: 60 s

The parameter

tDTO

is used for adjusting the time period

during which the switch-on condition

DT O

must be per-

manentely fulfilled.

Filling time
tFLL

:

Filling time
Adjustment range:
1.0 ... 30.0 min
in steps of 0.5 min
Factory setting: 5.0 min

The filling time can be adjusted using the parameter

tFLL

.

During this period, the pump runs at 100 % speed.

Stabilization
tSTB

:

Stabilization
Adjustment range:
1.0 ... 15.0 min
in steps of 0.5 min
Factory setting: 2.0 min

The parameter

tSTB

is used for adjusting the time period

during which the switch-off condition

DT F

will be ignored

after the filling time has ended.

Booster function option
OBST

:

Booster function
Adjustment range: ON / OFF
Factory setting: OFF

This function is used for switching on a second pump when
filling the solar system. When solar loading starts, R2 is ener-
gized in parallel to R1. After the filling time (

tFLL

) has ended,

R2 is switched off.

Note:

The booster function is available in system layout 1
(Arr = 1) only.
The booster function will only be available if the
drainback option has been activated.

Drainback option

A drainback system permits the heat transfer fluid to drain
back into the holding tank when solar energy is not coll-
ected. The drainback option will initiate the filling of the
system when solar loading begins.
If the drainback option

ODB

is activated, the pump will

operate at 100 % speed for the adjusted filling time

tFLL

in order to fill the system with fluid from the holding tank.
After

tFLL

, pump speed will go down to the adjusted

minimum pump speed

nMn

. The switch-off conditions will

then be ignored for the stabilization time

tSTB

in order to

avoid the system from shutting down prematurely.
If the function is activated, the menu items described in the
following (

tDTO

,

tFLL

and

tSTB

) have to be adjusted:

Note:

The drainback option is only available in system
layouts with one tank and one collector (Arr 1,
2, 3, 8 and 9).

ODB:

Drainback option
Adjustment range: OFF / ON
Factory setting: OFF

Note:

A drainback system layout requires additional
components such as a holding tank. The drainback
option should only be activated if all components
required are properly installed.

Note:

When the drainback option

ODB

is activated, the

cooling functions

OCC

,

OSYC

and

OSTC

as well

as the antifreeze function

OCF

are not available.

If

OCC

,

OSYC

,

OSTC

or

OCF

have already

been activated before, they will be deactivated
again as soon as

ODB

is activated. They will remain

deactivated, even if

ODB

is deactivated later on.

Note:

When the drainback option

ODB

is activated,

the temperature differences

DT O

,

DT F

and

DT S

are set to a fixed adjustment. Additionally,

the adjustment range and the factory setting of
the collector emergency shutdown temperature

EM

changes (see the corresponding channel

descriptions for further information).
Previous adjustments made in these channels will
be overridden and have to be entered again if

ODB

is deactivated later on.

Note:

Viessmann Vitosol collectors cannot be used in
drainback systems.

«
...
43
44
45
46
47
...
»

Summary of Contents for SCU224





















































Reviews:

No comments