Viessmann SCU224 User Manual Download Page 44 | Manualshive

Page: 44 / 52

Viessmann SCU224 User Manual Download Page 44

©

Viessmann

5443203

|

44

SCU224

Evacuated tube collector function

O TC:

Evacuated tube collector
function
Adjustment range: OFF / ON
Factory setting: OFF

Note:

If the drainback option

ODB

is activated,

TCRU

will not be available. In that case, the runtime
is determined by the parameters

tFLL

and

tSTB

.

TCEN:

Tube collector function
ending time
Adjustment range:

00:00 ... 23:45
in steps of 00:15
Factory setting: 19:00

TCST:

Tube collector function
starting time
Adjustment range:

00:00 ... 23:45
in steps of 00:15
Factory setting: 07:00

TCRU:

Tube collector function
runtime
Adjustment range: 5 ... 500 s
in steps of 5 s
Factory setting: 30 s

TCIN:

Tube collector function
standstill interval
Adjustment range: 1 ... 60 min
in steps of 1 min
Factory setting: 30 min

This function helps overcome the disadvantages caused by
the non-ideal sensor position with some tube collectors.
This function is not required with the Vitosol 300-T, but is
required for the Vitosol 200-T.

This function operates within an adjusted time frame (be-
ginning at

TCST

and ending at

TCEN

). It activates the

collector circuit pump for an adjustable runtime (

TCRU

)

between adjustable standstill intervals (

TCIN

) in order to

compensate for the delayed temperature measurement.

If the runtime

TCRU

is set to more than ten seconds, the

pump will be run at 100 % for the first ten seconds of the
runtime. For the remaining runtime, the pump will be run
at the adjusted minimum speed

nMN

.

If the collector sensor is defective or the collector is blocked,
this function is suppressed or switched off.

In system layout 7 (Arr = 7) both collectors are operated
independently from each other by means of this function. If
the tank is being loaded by one collector, the other one is
nevertheless operated after the adjusted standstill time.

Energy metering

OHQM

: Energy metering

Adjustment range: OFF / ON
Factory setting: OFF

If OHQM is activated, the heat quantity gained can be calcu-
lated and displayed. Energy metering is possible on Arr. 1, 3,
4, 5 and 10 if a flowmeter is used. To enable energy metering,
proceed as follows:

Î

Read the flow rate (l/min) from the flowmeter at maxi-
mum pump speed and adjust it in the

FMAX

channel

Î

Adjust the heat transfer fluid and the concentration of
the antifreeze in the channels

MEDT

and

MED%

.

FMAX:

Flow rate in l/min

Adjustment range: 0.5 ... 100.0
in steps of 0.5
Factory setting: 6.0

MEDT:

Heat transfer fluid

Adjustment range: 0 ... 3
Factory setting: 1

MED%:

Antifreeze ratio

in Vol-% (MED% is hidden
when MEDT 0 or 3 is used.)
Adjustment range: 20 ... 70
in steps of 1 %
Factory setting: 45

Heat transfer fluid:

0 : Water
1 : Propylene glycol
2 : Ethylene glycol
3 : Tyfocor

®

LS / G-LS

Note:

If the system layout 10 has been selected and

OHQM

is activated, energy metering will be

interrupted when the 3-way-valve switches to
the heat dump.

Note:

When using Tyfocor HTL set

MEDT

to 1 and

MED%

to 50.

«
...
42
43
44
45
46
...
»

Summary of Contents for SCU224





















































Reviews:

No comments