manualshive.com logo in svg

Viessmann SCU224, User Manual, Page: 33 / 52

Share
Download
Viessmann SCU224 User Manual Download Page 33

© 

Viessmann 

5443203

33 

|

SCU224

The system screen (active system layout) shows the system 
selected on the controller. It consists of several system 
component symbols, which are – depending on the current 
status of the system – either flashing, permanently shown 
or hidden.

sensors

collector 1

collector 2

pumps

heating circuit

sensor

additional  symbol  for 
operation of the burner

valve

tank

tank heat exchanger

tank 2 or backup heating (with 
an additional symbol)

tank sensor 
at the top

valve

Pump

3-way valve 

The flow direction or the 
actual switching position is 
shown 

Heating circuit

Tanks

 1 and 2

with heat exchanger 

Backup heating

with burner symbol

Temperature sensor

System screen

system screen

green: 

everything OK

red/green flashing  initialization phase
 

manual operation

red flashing: 

sensor fault   
(sensor symbol is flashing quickly)

2.3 Flashing codes

LED flashing codes

System screen flashing codes

•

  Pumps are flashing during initialization phase

•

  Sensor symbols are flashing if the corresponding sensor 

display channel is selected.

•

  Sensors are flashing in the case of a sensor fault.

•

  Burner symbol is flashing if the backup heating is active

Collectors

with collector sensor

Summary of Contents for SCU224





















































Reviews:

No comments