Viessmann B2SB Installation And Service Instructions For Contractors Download Page 95

Page: 95 / 124

Fault code dis-
played

System characteristics

Cause

Measures

Burner in a fault state

Fan speed too low

Check fan, fan connecting cables
and fan power supply.
Press reset button

Burner in a fault state

Fan idle state or set speed
not reached

Check fan, check connecting ca-
bles to fan.
Press reset button

Burner in a fault state

Fan unit faulty.

Check fan unit, replace if required.
Press reset button

Burner in a fault state

Burner control unit fault

Check ignition electrode, ionisation
electrode and connecting cables.
Check whether a strong interfer-
ence (EMC) field exists near the
appliance.
Press reset button

If the fault occurs sporadically, re-
place the coding card.
Replace control unit if fault is per-
manent.

Burner in a fault state and ad-
ditional fault B7 is displayed.

Boiler coding card miss-
ing.

Insert the boiler coding card.
Press reset button

Replace control unit if fault per-
sists.

Burner blocked or in a fault
state

Boiler coding card or main
PCB faulty, or incorrect
boiler coding card

Press reset button

. If the fault

persists, check the boiler coding
card and replace boiler coding card
or control unit if necessary.

Burner blocked or in a fault
state

Internal fault or reset but-
ton

blocked.

Restart the appliance. Replace the
control unit if the appliance will not
restart.

Note

If subscriber faults occur,

"Error, subscriber ..."

is dis-

played.

Troubleshooting

Fault codes

(cont.)

5778741

Diagnosis

Summary of Contents for B2SB





























































































































Search results

Summary of Contents for B2SB

Reviews:

Related manuals for B2SB

Brands by name

Popular brands

Viessmann B2SB, Installation And Service Instructions For Contractors

Search results

Summary of Contents for B2SB

Reviews:

Related manuals for B2SB

Brands by name

Popular brands