Viessmann B2SB Installation And Service Instructions For Contractors Download Page 33

Page: 33 / 124

Menu point

Settings and explanations

"Energy cockpit"

■

"ON"

The Energy cockpit with various scanning options is displayed.

■

"OFF"

The Energy cockpit is not displayed.

"Flue system"

(not Vitodens 3xx)

■

"Single connection"

Only one boiler is connected to the flue system.

■

"Multiple connections"

Several boilers are connected to the flue system.

Calling up the commissioning assistant at a later
point

If you need to continue commissioning later, the com-
missioning assistant can be reactivated at any time.

Tap the following buttons:

1. "Menu"

2. "Service"

Enter

"viservice"

password.

4. "Commissioning"

Extended commissioning assistant

Call up the commissioning assistant with

"Yes"

A safety instruction is shown on the display.

Note

The extended commissioning assistant can be
skipped with

"No"

After successfully reviewing the safety instruction,
tap

"Yes"

to confirm. This starts detection of the

connected sensors and the system components
connected via KM-BUS.
This process may take some time.

After detecting the devices, tap

"Next"

A list of detected system components (device list)
appears on the display.

Compare the device list with the system compo-
nents actually connected.
If any components were not detected, these can be
added later via the relevant parameters.

Commissioning, inspection, maintenance

Commissioning the system with the commissioning…

(cont.)

5778741

Summary of Contents for B2SB





























































































































Search results

Summary of Contents for B2SB

Reviews:

Related manuals for B2SB

Brands by name

Popular brands

Viessmann B2SB, Installation And Service Instructions For Contractors

Search results

Summary of Contents for B2SB

Reviews:

Related manuals for B2SB

Brands by name

Popular brands