Viessmann B2HB008 Installation Instructions Manual Download Page 49

Page: 49 / 64

Vitodens 200-W B2HB 19 to 35, 68 to 125 Installation

5461 884 - 14

Control Connections

Connecting the Outdoor Temperature Sensor

1. Remove cover of outdoor temperature sensor.
2. Mount wall-mount base (cable entry must point

downward).

3. Route cable from the boiler control board to the

outdoor sensor. Connect cable to sensor terminals

(wires are interchangeable).

Cable specifications:

2-wire cable, max. cable length 95 ft. (35 m) with a

wire size of min. AWG 16 copper.

4. Connect the outdoor temperature sensor to terminals

X 3.1/X3.2 on the boiler control board (wires are

interchangeable).

5. Place cover on base and snap into place.

IMPORTANT

The outdoor temperature sensor should be mounted 6.6

to 8.2 ft. (2 to 2.5 m) above ground level on the north or

northwest wall of the building. In case of a multi-storey

building, mount outdoor temperature sensor in the upper

half of the second floor.

Ensure that sensor is not located above windows, doors

and air vents, or immediately underneath a balcony or

gutter.

The outdoor temperature sensor must not be covered

by plaster. If mounting on an unplastered wall, make

allowances for thickness of plaster or remove sensor

before plastering wall.

IMPORTANT

Cable to the outdoor sensor must not be laid near line

voltage wiring (120/240V).

Summary of Contents for B2HB008

































































Search results

Summary of Contents for B2HB008

Reviews:

Related manuals for B2HB008

Brands by name

Popular brands

Viessmann B2HB008, Installation Instructions Manual

Search results

Summary of Contents for B2HB008

Reviews:

Related manuals for B2HB008

Brands by name

Popular brands