Viessmann B2HB008 Installation Instructions Manual Download Page 10

Page: 10 / 64

Vitodens 200-W B2HB 19 to 35, 68 to 125 Installation

5461 884 - 14

General Information/Set-up

Note:

The Vitodens 200-W, B2HB boiler has passed the

zero inches vent clearance to combustibles testing

requirements dictated by the boiler Harmonized

Standard ANSI Z21.13. CSA 4.9.2007 and

therefore is listed for zero clearance to combustibles

when vented with a single-wall special venting

system (AL-29-4C material) or UL/ULC-listed

CPVC/PPs gas vent material. The zero inches

vent clearance to combustibles for the Vitodens

200-W, B2HB boiler supercedes the clearance to

combustibles listing that appears on the special

venting system label.

Before placing boiler in its installation location, ensure all

necessary accessories are installed.

Minimum Clearances

CAUTION

The boiler must be installed in such a way that gas

ignition system components are protected from water

(spraying, splashing, etc.) during boiler operation and

service.

Table 1 Clearances
Top

Front

Rear

Left

Right Vent pipe

0 AL CL

Recommended minimum service clearances

For typical Vitodens installations, Viessmann recommends

installing the boiler with the clearances shown in the

illustration on the left.

Note:

The 12 in. (305 mm) side clearance specified is

only recommended to be able to view the boiler

certified rating plate, decal and also accommodate

the PRV installation kit.

If the pressure relief valve is rotated 90º facing forward

by using an extension between the tee and the boiler

connection, then this clearance can be reduced to

in.

(12 mm). This

in. (12 mm) clearance is only required

to be able to remove the boiler’s front cover and view

the rating plate attached to it, if needed.

This reduced clearance is also used in Vitodens multiple

boiler installation system as described in

the multiple boiler installation instructions.

The Vitodens 200-W, B2HB boiler is approved for closet

and alcove installation with the following clearances to

combustibles.

AL = Alcove

CL = Closet

Before Set-up

See the Vitodens 200-W B2HB Venting

System Installation Instructions for details.

Summary of Contents for B2HB008

































































Search results

Summary of Contents for B2HB008

Reviews:

Related manuals for B2HB008

Brands by name

Popular brands

Viessmann B2HB008, Installation Instructions Manual

Search results

Summary of Contents for B2HB008

Reviews:

Related manuals for B2HB008

Brands by name

Popular brands