background image

Vitodens 200-W B2HB 19 to 35, 68 to 125 Installation

5461 884 - 14

58

Technical Data

Additional Information

Boiler Model No. 200-W B2HB

19, 68

26, 94

35, 125

CSA input Natural Gas (NG)

CSA input Liquid Propane Gas (LPG)

CSA output/DOE

 

*1

heating capacity NG
CSA output/DOE

 

*1

 

heating capacity LPG
Net AHRI rating

 

*2

MBH

(kW)

MBH

(kW)

MBH

(kW)

MBH

(kW)

MBH

(kW)

12-68

(3.5-20)

12-68

(3.5-20)

11-64

(3.2-19)

11-64

(3.2-19)

55

(16)

19-94

(5.5-27)

31-94

(9-27)
18-89

(5-26)

29.5-89

(8.6-26)

77

(22)

19-125

(5.5-37)

31-125

(9-37)

18-117

(5-34)

29.5-117

(8.6-34)

102

(30)

Heat exchanger surface area

ft.

2

(m

2

)

12.96

(1.2)

12.96

(1.2)

12.96

(1.2)

Min. gas supply pressure

Natural gas

Liquid propane gas

“w.c.

“w.c.

4

10

4

10

4

10

Max. gas supply pressure 

*3

Natural gas

Liquid propane gas

“w.c.

“w.c.

14

14

14

14

14

14

A.F.U.E.

%

95

95

95

Weight

lbs

(kg)

110

(50)

110

(50)

110

(50)

Boiler water content

USG

(L)

1.02

(3.88)

1.02

(3.88)

1.02

(3.88)

Boiler max. flow rate

 

*4

GPM

(L/h)

6.2

(1400)

6.2

(1400)

6.2

(1400)

Max. operating pressure

at 210ºF (99ºC)

psig

bar

45

3

45

3

45

3

Boiler water temperature

- Adjustable high limit (AHL) range

  space heating (steady state)

  

  DHW production

- Fixed high limit (FHL)

ºF

(ºC)

ºF

(ºC)

ºF (ºC)

68 to 165

(20 to 74)

165

(74)

210 (99)

68 to 180

(20 to 82)

185

(82)

210 (99)

68 to 180

(20 to 82)

185

(82)

210 (99)

Boiler connections

Boiler heating supply and return   

Pressure relief valve 

 

Drain valve 

 

 

Boiler supply/return for 

indirect-fired DHW storage tank 

(field supplied)

Gas valve connection 

 

NPTM

NPTF

(male 

thread)

NPT

NPTF

¾ in.

¾ in.

¾ in.

¾ in.

¾ in.

¾ in.

¾ in.

¾ in.

¾ in.

¾ in.

¾ in.

¾ in.

¾ in.

¾ in.

¾ in.

*1

   Output based on 140ºF (60ºC), 120ºF (49ºC) system supply/return temperature.

*2

   Net AHRI rating based on piping and pick-up allowance of 1.15.

*3

   If the gas supply pressure exceeds the maximum gas supply pressure value, a separate gas pressure regulator 

 

must be installed upstream of the  heating system.

*4

   See “Waterside Flow” starting on page 30 in this manual.

Summary of Contents for B2HB008

































































Reviews: