Viessmann B2HB008 Installation Instructions Manual Download Page 35

Page: 35 / 64

Vitodens 200-W B2HB 19 to 35, 68 to 125 Installation

5461 884 - 14

Boiler Connections

System Layout 3

Vitodens 200-W, B2HB with...

- DHW storage tank

- one heating circuit with mixing valve and system separation

Installation of ...

■

underfloor heating circuit with 3-way mixing valve

and system separation (low-temp. circuit)

■

DHW

production

... with the following flow conditions:

The flow rate of the heating circuit is less than the

maximum possible water flow rate of the Vitodens

200-W B2HB boiler.
See page 30 for maximum water flow rate of the Vitodens

200-W B2HB boilers. The use of a low-loss header is

recommended if the system water flow rate is unknown.

The low-loss header is available as accessory part.
See following pages for installation examples with a

low-loss header.

System separation is required of underfloor heating

systems employing non-oxygen diffusion barrier tubing.

All components on the secondary side of the heat

exchanger must be made of corrosion-resistant materials.

Sizing of field-supplied pump

is critical for proper

boiler operation in this system layout. See page 30 for the

water flow pressure drop of the boiler heat exchanger.

An undersized pump may cause short-cycling and/or

improper operation of the boiler. Viessmann STRONGLY

recommends using a low-loss header and a boiler pump in

this system layout.

IMPORTANT

Legend

Vitodens 200-W B2HB boiler with

Vitotronic 200, HO1B outdoor reset

control

Outdoor temperature sensor

Vitotrol remote (optional)

Underfloor heating circuit

Mixing valve temperature sensor

Pressure relief valve

Plate heat exchanger for system

separation

Accessory kit for heating circuit with

mixing

valve

DHW circulating pump

DHW storage tank

DHW tank temperature sensor

Expansion

tank

DHW recirculation pump

28/20

Temperature and pressure relief valve

Flow check valve

Heating circuit pump

* Function based on coding of address 53

DHW circulating pump

must pump into the Vitodens

200-W B2HB boiler (as illustrated).

Summary of Contents for B2HB008

































































Search results

Summary of Contents for B2HB008

Reviews:

Related manuals for B2HB008

Brands by name

Popular brands

Viessmann B2HB008, Installation Instructions Manual

Search results

Summary of Contents for B2HB008

Reviews:

Related manuals for B2HB008

Brands by name

Popular brands