Viessmann B2HB008 Installation Instructions Manual Download Page 30

Page: 30 / 64

Vitodens 200-W B2HB 19 to 35, 68 to 125 Installation

5461 884 - 14

Boiler Connections

Waterside Flow

Waterside flow (primary circuit)

The Vitodens 200-W, B2HB is designed for closed loop,

forced circulation hot water heating systems only.
Use standard friction loss method for pipe sizing. Observe

boiler maximum and minimum flow rate limitations.

If system flow rate exceeds boiler maximum flow rate

(as stated above), falls below the minimum flow rate

or if system flow rate is unknown, Viessmann strongly

recommends the installation of a low-loss header.
Once the low-loss header is connected, the built-in low-

loss header logic of the Vitodens 200-W boiler ensures

the required



t across the system through the sensory

communication between the low-loss header and the

boiler.
An alternative method may be used, such as primary

secondary piping using closely spaced tees. A low-loss

header offers additional benefits not provided by a pair

of closely spaced tees. Viessmann therefore strongly

recommends and prefers the use of a low-loss header

over closely spaced tees. Refer to the Technical Data

manual for low-loss header information.

Model B2HB 26, 94

1 boiler

Output (NG/LPG)

MBH



t for NG/LPG

20ºF (11ºC) rise GPM (L/h)

8.8 (1999)

25ºF (14ºC) rise GPM (L/h)

7.0 (1599)

30ºF (17ºC) rise GPM (L/h)

5.9 (1332)

35ºF (19.5ºC) rise GPM (L/h)

5.0 (1142)

40ºF (22ºC) rise GPM (L/h)

4.4 (999)

Boiler maximum flow rate 6.2 GPM (1400 L/h)

Pressure drop (primary circuit) for

Vitodens 200-W, B2HB 19, 26, 35, 68, 94, 125

For sizing an on-site circulation system.

Max. flow rate: 6.2 GPM (1400 L/h)

Model B2HB 19, 68

1 boiler

Output (NG/LPG)

MBH



t for NG/LPG

20ºF (11ºC) rise GPM (L/h)

6.4 (1453)

25ºF (14ºC) rise GPM (L/h)

5.1 (1163)

30ºF (17ºC) rise GPM (L/h)

4.3 (969)

35ºF (19.5ºC) rise GPM (L/h)

3.7 (830)

40ºF (22ºC) rise GPM (L/h)

3.2 (727)

Model B2HB 35, 125

1 boiler

Output (NG/LPG)

MBH

117



t for NG/LPG

20ºF (11ºC) rise GPM (L/h)

11.7 (2657)

25ºF (14ºC) rise GPM (L/h)

9.4 (2126)

30ºF (17ºC) rise GPM (L/h)

7.8 (1771)

35ºF (19.5ºC) rise GPM (L/h)

6.7 (1518)

40ºF (22ºC) rise GPM (L/h)

5.9 (1328)

Flow rate

Supply head pressure (water)

Summary of Contents for B2HB008

































































Search results

Summary of Contents for B2HB008

Reviews:

Related manuals for B2HB008

Brands by name

Popular brands

Viessmann B2HB008, Installation Instructions Manual

Search results

Summary of Contents for B2HB008

Reviews:

Related manuals for B2HB008

Brands by name

Popular brands