Viessmann B2HB008 Installation Instructions Manual Download Page 13

Page: 13 / 64

Vitodens 200-W B2HB 19 to 35, 68 to 125 Installation

5461 884 - 14

Wall Mounting

Boiler Connections

Installing the wall mounting bracket

The Vitodens 200-W B2HB can be wall-mounted on a

concrete wall.

Note:

The enclosed screws and plastic anchors are

only suitable for concrete. For other construction

materials, use bolts and anchors that are suitable

for 115 lb (52 kg) loads.

Installation of mounting bracket on brick/concrete wall

1. Drill

holes

in. (12 mm).

2. Install rawl plugs and screw mounting bracket

wall.

3. Ensure the mounting bracket is level.

CAUTION

Whichever mounting method is used, ensure that the

bracket is tightly and securely fastened to wall. Failure

to secure boiler properly could cause boiler to loosen,

posing a severe safety hazard.

Fitting the wall mounting bracket

Following are the installation instructions for the mounting

bracket on each material. See the instructions applicable

to your installation requirements.

Summary of Contents for B2HB008

































































Search results

Summary of Contents for B2HB008

Reviews:

Related manuals for B2HB008

Brands by name

Popular brands

Viessmann B2HB008, Installation Instructions Manual

Search results

Summary of Contents for B2HB008

Reviews:

Related manuals for B2HB008

Brands by name

Popular brands