manualshive.com logo in svg

Vicon Extra 532, Service Manual, Page: 69 / 90

Share
Download
Vicon Extra 532 Service Manual Download Page 69

Cutter bar repair

Change of bearing 
intermediate gearwheel 

Cutter bar repair

Change of bearing 
intermediate gearwheel 

Cutter bar repair

Change of bearing 
intermediate gearwheel 

Cutter bar repair

Change of bearing 
intermediate gearwheel 

•

Remove tool T1 from the gear 
wheel and remove all the 
broken parts (typically 5 
pieces) of the circlip “A”.

NB! 

Make sure that all the 

broken parts from the circlip is 
removed from the intermediate 
gear wheel.

•

Place the gear wheel on top of 
tool T3.

NB! 

The recessed surface has to 

be faced upwards.

•

Make sure the gear wheel and 
the new bearing is facing the 
right way.

NB! 

The groove in the bearing 

and

in the gear wheel has be faced
downward.

•

Place tool T2 on top of the 
gear wheel as shown. 

•

Place the new circlip in the 
groove on the bearing.

•

Place the bearing in the cone 
shaped tool T2.

NB! 

The largest diameter of the 

tool has to be faced upwards.

4.8.1 Cutter bar-repair instructions

69

Summary of Contents for Extra 532



























































































Reviews:

No comments