manualshive.com logo in svg

Vicon Extra 532, Service Manual, Page: 32 / 90

Share
Download
Vicon Extra 532 Service Manual Download Page 32

Repair of friction clutch

Repair of friction clutch

Repair of friction clutch

Repair of friction clutch

Repair of friction clutch

Repair of friction clutch

Repair of friction clutch

Repair of friction clutch

When the torque for the friction 
clutch is too low, the friction disc 
should be replaced. The friction 
discs on the friction clutch are 
changed as follows: 

•

Tighten all the bolts on the 
friction clutch.

•

Remove the circlip shown.

•

Take the lock on the friction 
clutch apart and remove it.

•

Bend back the edges of the 
clutch housing shown. 

•

Take the friction clutch apart 
and replace the friction discs.

•

Assemble the friction clutch. 

•

Bend the edges of the clutch 
housing shown back in again.

•

Fit and assemble the lock.

•

Fit the circlip. 

•

Loosen all bolts on the friction 
clutch. 

Note; 

The settings for the 

coupling's springs cannot be 
adjusted.

•

Torque is 1500Nm.

Note; 

The settings for the 

coupling's springs cannot be 
adjusted.

4.1 PTO - Clutch

32

Summary of Contents for Extra 532



























































































Reviews:

No comments