manualshive.com logo in svg

Viavi Seeker HL, User Manual, Page: 22 / 36

Share
Download
Viavi Seeker HL User Manual Download Page 22

Seeker HL User’s Guide

Document Num., Rev. 2

May 2018

Page 22

Low Battery Warning

PC Communications Mode

This mode is used by the Seeker Setup software to send and 

retrieve configuration parameters from your Seeker HL. To enter 

this mode, connect the Seeker HL to a PC or laptop computer 

using a mini-USB charge / data cable and then open the Seeker 

Setup software to communicate with the Seeker HL. The screen 

shown to the right will be displayed while your Seeker HL is in this 

mode.

PC Communication Mode

Basic Operation

Power On/Off

Press and hold the red 

ON/OFF

 button until you hear three ascending tones. Within a few 

moments your Seeker HL will startup into the RF Signal Measurement Mode.

Low Battery Warning

A very low battery may cause the Seeker HL not to turn on. When 

the battery is too low for your Seeker HL to function, the screen 

shown to the right will appear. The battery must be charged for a 

few minutes before using again.

Summary of Contents for Seeker HL





































Reviews:

No comments