background image

Page 33 of  85

viasis 3003 user manual

via

traffic
controlling
gmbh

6.3.4  Menu Speed display options

The menu

Speed display options

is shown if you choose

4

 in the

Settings

 menu:

Speed display options:

1. Decimal places:  off

2. Minimal speed displayed: 5 km/h

3. Maximal speed displayed: 199 km/h

4. Threshold blinking LED: 200 km/h

5. Threshold Led mixed color: 200 km/h

6. Threshold LED color change: 200 km/h

7. Back

Your choice 1...7?

The parameter values shown above are the default values ex factory.

For  viasis  LED  displays  with  only  one  LED  color  the  options

Threshold LED mixed color

and

Threshold LED color change

 do not exist. The

Threshold LED mixed color

is only

shown for viasis with two appropriate LED colors. The options given in menu “Speed display
options”, with exception of the Decimal places, need to be defined for each activated parame-
ter set.

6.3.4.1 Decimal places

For applications where low vehicle speeds shall be measured exactly, e. g. for drive in weigh-
bridges, the display of a decimal digit until 19,9 km/h (or mph) can be activated by entering

1

in the

Speed display options

menu and further activating the decimal:

Decimal places

1. off

2. on

Your choice 1...2?

If vehicle speeds above or equal 20 km/h are measured the speed values are displayed on the
numeric LED display as whole numbers again. If the speed decimal is activated the speed data
output in the

Online measurement

 (chapter 6.6) mode, is also given with a decimal digit.

The setting for decimal places is a general setting equal for all parameter sets.

6.3.4.2 Minimal - and maximal speed displayed

The „

Minimal speed displayed

“ is the lowest measured speed value published on the numeric

LED speed display

In the “Settings” menu you are prompted after the selection

4

:

Minimal speed displayed = _

End the numbers input with <

return

 >. The new value is shown in the menu immediately.

The values for minimum speed can be set in the range between 5 and 199 km/h. Only values
lower or equal the adjusted maximum speed will be accepted by the system.

Summary of Contents for Viasis 3003


























































































Reviews: