VESPA 633844 IT Service Manual Download

Page: 163 / 308

- Fuel pump

- HV coil

- Injector

The control unit is provided with a self-diagnosis

system connected to an indicator light in the in-

strument panel.

Failures are detected and restored by the diag-

nostic tester.

In any case, when the fault is no longer present,

the data storage is automatically cleared after 16

cycles of use (cold start, running at regular engine

temperature, stop).

The diagnostic tester is also required to adjust the

idle mixture.

Specific tooling

020460Y

Scooter diagnosis and tester

The MIU injection-ignition system carries out

checks on the rpm counter and the electric fan for

radiator cooling.

The MIU control unit has a decoder for the anti-

theft immobiliser.

The MIU control unit is connected to a diagnostic

LED on the instrument panel, that also carries out

the deterrent flashing functions.

The MIU control unit power supply is furthermore controlled by the emergency switch; that is to provide

further safety for the scooter.

Vespa GTV 250 i.e.

Injection

INJEC - 3

Summary of Contents for 633844 IT





















































































































































































































































































































Search results

Summary of Contents for 633844 IT

Reviews:

Related manuals for 633844 IT

Brands by name

Popular brands

VESPA 633844 IT, Service Manual

Search results

Summary of Contents for 633844 IT

Reviews:

Related manuals for 633844 IT

Brands by name

Popular brands