VESPA 633844 IT Service Manual Download Page 110

Page: 110 / 308

- Fit the steel shim in contact with the bushing and

the stationary drive pulley.

- Install the appropriate tool as described in the re-

moval phase.

-Tighten the nut with washer to the prescribed tor-

que.

Specific tooling

020626Y

Driving pulley lock wrench

Locking torques (N*m)

Drive pulley nut

75 ÷ 83

Refitting the transmission cover

- Check the presence of the 2 centring dowels and

the correct installation of the sealing gasket for the

oil sump on the transmission cover.

- Replace the cover tightening the 10 screws at the

specified torque.

- Refit the oil loading cap/bar.

- refit the steel washer and the driven pulley nut.

- Tighten the nut to the prescribed torque using the

lock wrench and the torque wrench tools.

- Replace the plastic cover.

Specific tooling

020423Y

driven pulley lock wrench

Locking torques (N*m)

Transmission cover screws

11 ÷ 13

Driven pul-

ley shaft nut

54 ÷ 60

End gear

Engine

Vespa GTV 250 i.e.

ENG - 16

Summary of Contents for 633844 IT





















































































































































































































































































































Search results

Summary of Contents for 633844 IT

Reviews:

Brands by name

Popular brands

VESPA 633844 IT, Service Manual

Search results

Summary of Contents for 633844 IT

Reviews:

Brands by name

Popular brands