VESPA 633844 IT Service Manual Download Page 46

Page: 46 / 308

Braking system

Level check

The brake fluid tanks for the front and rear brakes

are located on the pumps under the handlebar

cover. Proceed as follows:

- Remove the brake pump cover

- Rest the vehicle on its centre stand with the han-

dlebars perfectly horizontal;

- Check the fluid level through the sight glass as

shown in the figure. A certain lowering of the level

is caused by wear on the pads.

Top-up

- Position the vehicle on a flat surface and on the

centre stand

- Remove the brake pump cover as indicated in the

photo

Check the brake fluid level through the sight glass

on the pump as shown in the photograph

- If the level is below the minimum, fill using the two

screws shown in the figure

- Remove the gasket and fill with DOT 4 until the spyglass is completely covered

For refitting purposes carry out the operations in the reverse order from the removal operation and

respect the tightening torque of the tank cover screws.

CAUTION

MAKE SURE THE BRAKE FLUID DOES NOT GET INTO YOUR EYES OR ON YOUR SKIN OR
CLOTHES. IF THIS HAPPENS ACCIDENTALLY, WASH WITH WATER.

CAUTION

Maintenance

Vespa GTV 250 i.e.

MAIN - 12

Summary of Contents for 633844 IT





















































































































































































































































































































Search results

Summary of Contents for 633844 IT

Reviews:

Brands by name

Popular brands

VESPA 633844 IT, Service Manual

Search results

Summary of Contents for 633844 IT

Reviews:

Brands by name

Popular brands