VESPA 633844 IT Service Manual Download

Page: 155 / 308

Removal

- Remove the transmission cover and the com-

plete driving pulley beforehand

- Install the base of the appropriate tool on the oil

guard using the screws provided.

Specific tooling

020622Y

Transmission-side oil guard punch

- Screw the threaded bar onto the base of the tool

and extract the oil guard.

Specific tooling

020622Y

Transmission-side oil guard punch

Refitting

- Use a new oil guard for the refitting

- Prepare the new oil guard, lubricating the sealing

lip.

- Preassemble the oil seal with the specific tool,

positioning the screws.

- Insert the sheath over the crankshaft.

- Insert the tool with the oil seal on the crankshaft

until it comes into contact with the crankcase.

- Insert the adaptor bushing of the tool in the hole

on the crankcase.

Vespa GTV 250 i.e.

Engine

ENG - 61

Summary of Contents for 633844 IT





















































































































































































































































































































Search results

Summary of Contents for 633844 IT

Reviews:

Related manuals for 633844 IT

Brands by name

Popular brands

VESPA 633844 IT, Service Manual

Search results

Summary of Contents for 633844 IT

Reviews:

Related manuals for 633844 IT

Brands by name

Popular brands