manualshive.com logo in svg

VESPA 633844 IT, Service Manual

The VESPA 633844 IT Service Manual is essential for maintaining and servicing your VESPA scooter. This comprehensive manual provides step-by-step instructions on troubleshooting, repairs, and maintenance procedures. Download this invaluable resource for free from manualshive.com and keep your scooter running smoothly for years to come.

Share
Download
background image

•Instrument panel lights

• Horn

• electric start up

• Engine stopping with emergency stop switch

• electric saddle opening button

CAUTION

TO ENSURE MAXIMUM PERFORMANCE, THE BATTERY MUST BE CHARGED BEFORE USE.
INADEQUATE CHARGING OF THE BATTERY WITH A LOW LEVEL OF ELECTROLYTE BEFORE
IT IS FIRST USED SHORTENS THE LIFE OF THE BATTERY.

CAUTION

WHEN INSTALLING THE BATTERY, ATTACH THE POSITIVE LEAD FIRST AND THEN THE NEG-
ATIVE LEAD.

WARNING

BATTERY ELECTROLYTE IS TOXIC AND IT MAY CAUSE SERIOUS BURNS. IT CONTAINS SUL-
PHURIC ACID. AVOID CONTACT WITH EYES, SKIN AND CLOTHING.
IN CASE OF CONTACT WITH EYES OR SKIN, RINSE WITH ABUNDANT WATER FOR ABOUT 15
MINUTES AND SEEK MEDICAL ATTENTION AT ONCE.
IF IT IS SWALLOWED, IMMEDIATELY DRINK LARGE QUANTITIES OF WATER OR VEGETABLE
OIL. SEEK IMMEDIATE MEDICAL ATTENTION.
THE BATTERIES PRODUCE EXPLOSIVE GAS; KEEP THEM AWAY FROM NAKED FLAMES,
SPARKS AND CIGARETTES. IF THE BATTERY IS CHARGED IN A CLOSED PLACE, TAKE CARE
TO ENSURE ADEQUATE VENTILATION. ALWAYS PROTECT YOUR EYES WHEN WORKING
CLOSE TO BATTERIES.
KEEP OUT OF THE REACH OF CHILDREN

CAUTION

NEVER USE FUSES WITH A CAPACITY HIGHER THAN THE RECOMMENDED CAPACITY. USING
A FUSE OF UNSUITABLE RATING MAY SERIOUSLY DAMAGE THE VEHICLE OR EVEN CAUSE
A FIRE.

Levels check

Level check:

- Hydraulic brake system liquid level.

- Rear hub oil level

- Engine coolant level

- Engine oil level

Road test

Test ride

- Cold start

- Instrument operations

- Response to the throttle control

- Stability on acceleration and braking

- Rear and front brake efficiency

- Rear and front suspension efficiency

Vespa GTV 250 i.e.

Pre-delivery

PRE DE - 3

Summary of Contents for 633844 IT





















































































































































































































































































































Reviews:

No comments

Related manuals for 633844 IT

Happy Trails HTP1-12-7 Quick Start Manual preview
HTP1-12-7
Brand: Happy Trails Pages: 3
R&G CP0556 Fitting Instructions Manual preview
CP0556
Brand: R&G Pages: 21
Apollo APOLLO 150 User Manual preview
APOLLO 150
Brand: Apollo Pages: 92
KTM 690 Enduro R AU/GB 2014 Setup Instructions preview
690 Enduro R AU/GB 2014
Brand: KTM Pages: 18
Spartus 901X User Manual preview
901X
Brand: Spartus Pages: 24
IRC SGRACE-CUT Instructions preview
SGRACE-CUT
Brand: IRC Pages: 2
Honda CB TWISTER (Spanish) Manual Del Propietario preview
CB TWISTER
Brand: Honda Pages: 93
Thunderbike Old style Manual preview
Old style
Brand: Thunderbike Pages: 7
Bosch GHJ 10,8+18V Unisex Original Instructions Manual preview
GHJ 10,8+18V Unisex
Brand: Bosch Pages: 14
Bosch LTE65 Manual preview
LTE65
Brand: Bosch Pages: 28
Bosch 06188000DY Original Instructions Manual preview
06188000DY
Brand: Bosch Pages: 145
hepco & becker 6304553 00 05 Mounting Instructions preview
6304553 00 05
Brand: hepco & becker Pages: 2
hepco & becker 5049515 00 05 Quick Start Manual preview
5049515 00 05
Brand: hepco & becker Pages: 3
Braaap Moto3 User Manual preview
Moto3
Brand: Braaap Pages: 40
APRILIA MANA 850 GT ABS Manual preview
MANA 850 GT ABS
Brand: APRILIA Pages: 197
Renegade COMMANDO User Manual preview
COMMANDO
Brand: Renegade Pages: 52
Beta RR 125 Instruction Manual preview
RR 125
Brand: Beta Pages: 260
Yadea C1S Service Manual preview
C1S
Brand: Yadea Pages: 88

Brands by name

Popular brands

Load more brands