manualshive.com logo in svg

VESPA 633844 IT, Service Manual

Share
Download
VESPA 633844 IT Service Manual Download Page 103

Inspecting the driven sliding half-pulley

- Remove the two internal grommets and the two

O-rings.

- Measure the movable half-pulley bushing inside

diameter.

- Check the contact surface with the belt to make

sure there are no flaws.

- Check the riveted joints are functional.

- Check the evenness of the belt faying surface.

MOVABLE DRIVEN HALF-PULLEY DIMENSIONS

Specification

Desc./Quantity

Wear limit

0.3 mm

standard diameter

Diameter 41.000 - 41.035 mm

maximum allowable diameter

Ø 41.08 mm

Refitting the driven half-pulley bearing

- Support the pulley bushing adequately from the

threaded side using a wooden surface.

- Fit a new roller sleeve as in the figure.

- For the fitting of the new ball bearing, follow the

example in the figure using a modular punch.

Fit the retention ring

WARNING

N.B.

FIT THE BALL BEARING WITH THE VISIBLE
SHIELD

Specific tooling

020376Y

 

Adaptor handle

020375Y

 

Adaptor 28 x 30 mm

020424Y

 

Driven pulley roller casing fitting

punch

Vespa GTV 250 i.e.

Engine

ENG - 9

Summary of Contents for 633844 IT





















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands