background image

Vertiv™ NetSure™ IPE Series -48 VDC Outdoor Rectifier Installation and User Manual 

Proprietary and Confidential © 2022 Vertiv Group Corp. 

11 

DC Power Terminals: 

Test Level 

Source 

Impedance 

Performance 

Criteria 

Line to Line 

Line to Ground 

± 500 V 

± 500 V 

2 ohms 

± 800 V 

± 800 V 

2 ohms 

The test method is described in EN 61000-4-5.  In this test the DC-cables 
shall be 5 m long. 

DC Power Port, Common Mode (12 ohms impedance): 

Minimum Peak 

Voltage (volts) 

Voltage Maximum 

Rise/Minimum Decay 

Time (

µ

s) 

Minimum Peak 

Current per 

Conductor (amperes) 

Current Maximum 

Rise/Minimum Decay 

Time (

µ

s) 

Repetitions, each 

Polarity 

±

 1000 

1.2/50 

8/20 

The EUT (Equipment Under Test) shall not be damaged and shall continue to operate properly after the 
application of the first-level surge. 

Requirements on RS485, CAN-bus Signals Are: 

Minimum Peak Voltage 

(volts) 

Voltage Maximum 

Rise/Minimum Decay 

Time (

µ

s) 

Minimum Peak 

Current per 

Conductor (amperes) 

Current Maximum 

Rise/Minimum Decay 

Time (

µ

s) 

Repetitions, each 

Polarity 

±

 1000 (lines to ground) 

10/700 

5/320 

Requirements on CAN-bus signals are 1kV diff. /2kV com. criteria B with 42ohms source impedance. 

According Telcordia GR-1089-CORE issue 7:2017: 

Requirements on CAN-bus signals are: 

Surge 

Minimum Peak 

Voltage (volts) 

Minimum Peak Current 

per Conductor 

(amperes) 

Maximum Rise/ Minimum Decay 

Time for Voltage and Current 

(us) 

Repetitions, each 

Polarity 

Performance 

criterion 

800 

100 

2/10 

1500 

100 

2/10 

 

6.

 

Single Rectifier Audible Noise:  At 25 °C ≤42 dB(A).  Measurement made at 0.6 m distance in front of rectifier and at the 
center of the rectifier. 

7.

 

Overvoltage Category (per IEC/UL62368-1):  III 

8.

 

Power Distribution System:  TN/TT/IT 

9.

 

Pollution Degree:  Degree 3, as per UL/ IEC/EN62368-1. 

Summary of Contents for 1R482000C2-1









































































































Reviews: