Vertiv 1R482000C2-1 Installation And User Manual Download Page 100

Page: 100 / 104

Vertiv™ NetSure™ IPE Series -48 VDC Outdoor Rectifier Installation and User Manual

Table 8.1

Alarm Name

Alarm Description

Action to Correct

Battery Temp High

Battery temperature is higher than High alarm

setting.

Check why temperature is high.

Battery Temp High+

Battery temperature is higher than High+ alarm

setting.

Check why temperature is high.

Battery T No Probe

Battery temperature sensor port is not used.

Temperature probe is enabled but not plugged

in.

Battery T Probe Error

Battery temperature sensor failure.

Replace temperature probe.

CAN Communication Failure

CAN bus communications failure.
No devices communicating on CAN bus.

Check communications cables.

Rectifier Lost

A rectifier cannot be detected by the controller.

Reset the Rectifier Lost alarm. Replace

defective rectifier.

HW SelfDetect

Controller self-detection test fails.

Replace the rectifier.

Manual Mode

Controller in manual mode.

Batt Discharge

Battery is discharging.

A battery test is active (the discharge test will

stop automatically). There is a mains failure

(check that it is not caused by open AC input

circuit breaker). The system load is higher than

rectifier capacity, causing the batteries to

discharge (install additional rectifiers).

Rect Overload

Output overload condition.

Check the load.

Save Power

Rectifier in Save Power mode.

MultiRect Alarm

More than one rectifier has failed or a Mains

Failure.

Check input voltage to rectifiers. Replace

rectifiers.

DI0 Alarm

Digital input DI0 alarm is active.

Check why alarm is active.

Rectifier Failure

A rectifier has a fault condition.

Correct the rectifier fault.

Rectifier Protected

A rectifier is in protected mode.

Rectifier Fan Failure

A rectifier’s fan has failed.

Replace fan.

Rectifier Over Temperature

A rectifier has a high temperature condition.

Check why temperature is high.

Rectifier Power Limited

NOT IMPLEMENTED AT THIS TIME

Rectifier AC Failure

No AC input power to a rectifier.

Check why no AC input power available.

Rectifier Sharing Current Alarm

A rectifier has a current sharing alarm.

Rectifier HVSD (AC Over Voltage Shut Down)

A rectifier has an overvoltage condition.

Correct the rectifier fault.

Rectifier No Response

A rectifier has lost communications with the

controller.

Check communications cables. Replace the

rectifier.

Alarm-Block Level

MPPT Overwork Alarm

Summary of Contents for 1R482000C2-1









































































































Search results

Summary of Contents for 1R482000C2-1

Reviews:

Related manuals for 1R482000C2-1

Brands by name

Popular brands

Vertiv 1R482000C2-1, Installation And User Manual

Search results

Summary of Contents for 1R482000C2-1

Reviews:

Related manuals for 1R482000C2-1

Brands by name

Popular brands