Vertical TeleVantage 7.5 Install Manual Download | Manualshive

Page: 163 / 180

background image

A

PPENDIX

E. I

NTEL

D

IALOGIC

T

ELEPHONY

B

OARD

S

PECIFICATIONS

E-5

11.

Supported in standalone mode only. Voice resources on the board are not supported
by TeleVantage.

12.

Layer 3 QoS TOS Octet (used by DiffServe routers) is not supported.

13.

With a host-based VoIP stack, board must use u-law audio format (the default.)
Applies to:

Q

DM/IP241-1T1-P100: All media loads except iptk_t1_311

Q

DM/IP481-2T1-P100: All media loads except ipt_2isdn_5ess_311

Q

DM/IP241-1T1-P10: Media load ipvs_isdn_5ess_307 only

Q

DM/IP301-1E1-P10: Media load ipvs_isdn_net5_307 only

14.

With a host-based VoIP stack, board must use a-law audio format. Applies to all media
loads except iptk_e1_311.

15.

Includes an onboard 100BT NIC.

16.

Includes an onboard 10BT NIC.

17.

Uses the Server PC’s NIC (does not include an onboard NIC.)

18.

In most configurations, only 8 of the 12 analog trunk ports on the board are used, in
order to reserve 4 voice resources for use by stations. For the DI0408LSAR2 board,
applies to all media loads except DI0408LSA_REV2_ML5.

19.

Number of rings before trunk pickup cannot be changed for analog trunks on the
board. For the DI0408LSAR2 board, applies to all media loads except
DI0408LSA_REV2_ML5.

20.

The board supports the T1 ISDN PRI protocols 4ESS, 5ESS, DMS, and QSIG. CAS
protocols (including Robbed Bit T1) are not supported. For the following boards,
applies to certain media loads:

Q

DM/IP241-1T1-P100: All media loads except iptk_t1_311

Q

DM/IP481-2T1-P100: All media loads except ipt_2isdn-5ess-311

21.

The board supports the E1 ISDN PRI protocols Net5 and QSIG. CAS protocols
(including R2MF E1) are not supported. For the following boards, applies to certain
media loads:

Q

DM/IP301-1E1-P100: All media loads except iptk_e1_311

Q

DM/IP601-2E1-P100: All media loads except ipt_2isdn_net_-311

22.

Depending on the quality of your analog trunks, the maximum modem speed when
using this board will be 28.8 and 33.6 KB per second.

23.

SIP DTMF transmission via RFC2833 digits is not supported.

«
...
161
162
163
164
165
...
»

Summary of Contents for TeleVantage 7.5





















































































































































































Reviews:

No comments

Related manuals for TeleVantage 7.5

4116 - SCX B/W Laser

Brand: Samsung Pages: 14

2252W - Printer - B/W

Brand: Samsung Pages: 10

M7CL StageMix V1.5

Brand: Yamaha Pages: 20

Brand: Yamaha Pages: 80

Brand: MACROMEDIA Pages: 156

Veriteq viewLinc 4.0

Brand: Vaisala Pages: 168

Brand: Brocade Communications Systems Pages: 41

Brand: MACROMEDIA Pages: 830

APPLICATION STACK 1.3 RELEASE

Brand: Red Hat Pages: 26

Brand: Konica Minolta Pages: 6

Auto Configuration Server Vantage Access

Brand: ZyXEL Communications Pages: 113

Brand: AirLive Pages: 19

Brand: Sonifex Pages: 68

Application Accelerator RAID Edition

Brand: Intel Pages: 85

Brand: AMX Pages: 53

FINAL MIX VST - FOR TRACKTION

Brand: Mackie Pages: 26

Energy WeatherLink

Brand: Davis Instruments Pages: 47

Brand: Echo Audio Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands