manualshive.com logo in svg

Vega VEGAPULS 63, Operating Instructions Manual

Share
Download
Vega VEGAPULS 63 Operating Instructions Manual Download Page 9

9

3 Product description

VEGAPULS 67 • 4 … 20 mA/HART - four-wire

36532-EN-160224

This operating instructions manual applies to the following instrument 

versions:

• 

Hardware from 2.1.0

• 

Software from 4.5.1

The scope of delivery encompasses:

• 

Radar sensor

• 

Mounting strap with fixing material (optional)

• 

Documentation

 

– Quick setup guide VEGAPULS 67

 

– Instructions for optional instrument features

 

–

Ex-specific "

Safety instructions

" (with Ex versions)

 

–

If necessary, further certificates

• 

DVD "

Software

", included therein

 

– PACTware/DTM Collection

 

– Driver software

Information:

In the operating instructions manual, the optional instrument features 

are described. The respective scope of delivery results from the order 

specification.

3.2  Principle of operation

The VEGAPULS 67 is a radar sensor for continuous level measure-

ment of bulk solids under simple process conditions. It is suitable for 

smaller silos and vessels.
The instrument is also suitable for applications in liquids.

The antenna of the radar sensor emits short radar pulses with a 

duration of approx. 1 ns. These pulses are reflected by the product 

and received by the antenna as echoes. The transit time of the radar 

pulses from emission to reception is proportional to the distance and 

hence to the level. The determined level is converted into an appropri-

ate output signal and outputted as measured value.

3.3  Packaging, transport and storage

Your instrument was protected by packaging during transport. Its 

capacity to handle normal loads during transport is assured by a test 

based on ISO 4180.
The packaging of standard instruments consists of environment-

friendly, recyclable cardboard. For special versions, PE foam or PE 

foil is also used. Dispose of the packaging material via specialised 

recycling companies.

Transport must be carried out in due consideration of the notes on the 

transport packaging. Nonobservance of these instructions can cause 

damage to the device.

Scope of this operating 

instructions manual

Scope of delivery

Application area

Functional principle

Packaging

Transport

Summary of Contents for VEGAPULS 63





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands