manualshive.com logo in svg

Vega VEGAPULS 63, Operating Instructions Manual

Share
Download
Vega VEGAPULS 63 Operating Instructions Manual Download Page 43

43

6 Set up with the display and adjustment module

VEGAPULS 67 • 4 … 20 mA/HART - four-wire

36532-EN-160224

3.  Set the requested percentage value with 

[+]

 and save with 

[OK]

. 

The cursor jumps now to the distance value.

4.  Enter the appropriate distance value in m (corresponding to the 

percentage value) for the full vessel. Keep in mind that the max. 

level must lie below the min. distance to the antenna edge.

5.  Save settings with 

[OK]

To damp process-dependent measured value fluctuations, set an 

integration time of 0 … 999 s in this menu item.

Depending on the sensor type, the factory setting is 0 s or 1 s.

In the menu item "

Current output mode

" you determine the output 

characteristics and reaction of the current output in case of failure.

The default setting is output characteristics 4 … 20 mA, failure mode 

< 3.6 mA.

In the menu item "

Current output Min./Max.

", you determine the reac-

tion of the current output during operation.

Setup - Damping

Setup - Current output 

mode

Setup - Current output 

Min./Max.

Summary of Contents for VEGAPULS 63





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands