Vega VEGAPULS 63 Operating Instructions Manual Download Page 7

Page: 7 / 84

2 For your safety

VEGAPULS 67 • 4 … 20 mA/HART - four-wire

36532-EN-160224

•

The instrument must only be installed and maintained by appropri-

ately qualified staff

2.8 Radio license for USA/Canada

The instrument is in conformity with part 15 of the FCC regulations.

Take note of the following two regulations:

•

This device may not cause interference, and

•

This device must accept any interference, including interference

that may cause undesired operation of the device

Modifications not expressly approved by the manufacturer will lead to

expiry of the operating licence according to FCC/IC.
The instrument is in conformity with RSS-210 of the IC regulations.
The instrument may only be used in closed vessels made of metal,

concrete, or fibre-reinforced plastic.

2.9 Environmental instructions

Protection of the environment is one of our most important duties.

That is why we have introduced an environment management system

with the goal of continuously improving company environmental pro-

tection. The environment management system is certified according

to DIN EN ISO 14001.

Please help us fulfill this obligation by observing the environmental

instructions in this manual:

•

Chapter "

Packaging, transport and storage

•

Chapter "

Disposal

Summary of Contents for VEGAPULS 63





















































































Search results

Summary of Contents for VEGAPULS 63

Reviews:

Brands by name

Popular brands

Vega VEGAPULS 63, Operating Instructions Manual

Search results

Summary of Contents for VEGAPULS 63

Reviews:

Brands by name

Popular brands