Vega VEGAPULS 63 Operating Instructions Manual Download Page 15

Page: 15 / 84

4 Mounting

VEGAPULS 67 • 4 … 20 mA/HART - four-wire

36532-EN-160224

Fig. 5: Turning by fastening in the centre

4.4 Mounting instructions

For tight installation of the version with plastic horn antenna with com-

pression or adapter flange, the following conditions must be fulfilled:
1. Use suitable flat seal, e.g. of EPDM with Shore hardness 25 or 50
2. Make sure the number of flange screws corresponds to the num

ber of flange holes

3. Tighten all screws with the torque stated in the technical data

The emitted radar impulses of the radar sensor are electromagnetic

waves. The polarisation is the direction of the electrical share. With

radar sensors, the polarisation can be used to reduce the effect of

false echoes considerably by turning the instrument in the connection

flange or mounting boss.

The position of the polarisation is marked on the instrument.

Fig. 6: Position of the polarisation
1 Marking bar

Mount the instrument at least 200 mm (7.874 in) away from the vessel

wall.

200 mm

(7.87")

Fig. 7: Mounting the radar sensor on the vessel top

Tight installation of the

plastic horn antenna

Polarisation

Installation position

Summary of Contents for VEGAPULS 63





















































































Search results

Summary of Contents for VEGAPULS 63

Reviews:

Brands by name

Popular brands

Vega VEGAPULS 63, Operating Instructions Manual

Search results

Summary of Contents for VEGAPULS 63

Reviews:

Brands by name

Popular brands