TCI-W11-U, TCI-W22-U Universal Controller
O
UTPUT
C
ONFIGURATION
Doc: 70-00-0140C, V2.0-20220523
© Vector Controls LLC, USA
Page 17-24
Subject to alteration
Digital output configuration (1d, 2d)
Settings for digital outputs (1d00 / 2d00 = OFF, 1d05 / 2d05 = 0), 1d = DO1, 2d = DO2
Parameter Description
Range
Default
1d 00
Enable digital/PWM or floating point (3-point valve) output
OFF= DO1 and DO2 are two digital/PWM outputs
ON = DO1 and DO2 are one floating point output (DO1 open, DO2 close)
ON/OFF
OFF
1d 01
Select control loop or special function (0= OFF)
1= LP1, 2= LP2
3= Dehumidify (4 pipe, max LP1 cooling, LP2 direct)
4= Manual positioning (on/off)
5= State functions
0
–
5
0
1d 02
When 1d01 = 1, configure output:
0= Stage 1 heating/reverse
1= Stage 1 cooling/direct
2= Stage 1 heating and cooling, reverse and direct
3= Stage 2 heating/reverse
4= Stage 2 cooling/direct
5= Stage 2 heating and cooling, reverse and direct
If 1d01 = 4 Manual positioning or time schedule controlled
0= Time schedule controlled only
1= Manual positioning and time schedule controlled
When 1d01 = 5, select state functions:
0= ON if controller operation state is ON
1= ON while demand on any output
2= ON while controller in heating mode and operation state ON
3= ON while controller in cooling mode and operation state ON
0
–
5
0
1d 03
Switch-off delay (time output active with no more demand)
Delay is in seconds or minutes depending on d09
0
–
255
90sec
1d 04
Switch-on delay(time demand active before output on)
In state mode 1d01=5 outputs disabled during switch-on delay
Delay is in seconds or minutes depending on d09
0
–
255
5 sec
1d 05
Activate PWM, set cycle time, seconds (>0 activates, 0 deactivates)
0
–
1650s
0s
1d 06
Choose alarm to set output to ON (output OFF on conflicting alarms)
Alarm: 1 2 3 4 5 6 7 8
ALA1
–
ALA8
1d 07
Choose alarm to set output to OFF (output OFF on conflicting alarms)
Alarm: 1 2 3 4 5 6 7 8
ALA1
–
ALA8
1d 08
Display fan symbol while active
ON/OFF
OFF
1d 09
Binary switching delays in minutes or seconds
OFF = delays are in seconds, ON = delays are in minutes
ON, OFF
OFF
➔
Low and high limit alarms are defined with input parameters. With output parameters assign
an alarm to an output and select output state. Each alarm
’s required output
can be
individually selected. Multiple alarms can be signed to one output. Should one alarm be
simultaneously selected to activate and deactivate the output, the one to de-activate has
precedence.
➔
With manual positioning (1d01=4) position the output directly (ON/OFF).
➔
With dehumidifying (1d01=3) the maximum value is taken of cooling and dehumidifying. When the humidity is too high,
cooling will continue to operate, even without a demand for cooling, to dehumidify the air and heating will activate to
maintain comfort.
➔
State functions (1d01=5) activate the output based on certain conditions with or without a demand for heating or cooling,
in either occupied (comfort) or unoccupied (standby) mode. In Energy Hold OFF mode (EHO) the output will be off.
Output Priority
1. Alarm level low
2. Alarm level high
3. Operation mode OFF
4. Control function
