Varec 7532 Installation And Operation Manual Download Page 12

Page: 12 / 106

Mounting

Radar Tank Gauge

Installation and Operations Manual

3.2

Incoming acceptance, transport, storage

3.2.1

Incoming acceptance

Check the packing and contents for any signs of damage.

Check the shipment, make sure nothing is missing and that the scope of supply matches

your order.

3.2.2

Transport

Caution!

Follow the safety instructions and transport conditions for instruments of more than

18 kg. Do not lift the measuring instrument by its housing in order to transport it.

3.2.3

Storage

Pack the measuring instrument so that is protected against impacts for storage and

transport. The original packing material provides the optimum protection for this.

The permissible storage temperature is -40 °C…+80 °C.

Summary of Contents for 7532











































































































Search results

Summary of Contents for 7532

Reviews:

Related manuals for 7532

Brands by name

Popular brands

Varec 7532, Installation And Operation Manual

Search results

Summary of Contents for 7532

Reviews:

Related manuals for 7532

Brands by name

Popular brands