Valor RetroFire RF24JDN Installation Manual Download Page 2

Page: 2 / 49

Ce guide est disponible en français sur demande.

This appliance is a domestic room-

heating appliance. It must not be used

for any other purposes such as drying

clothes, etc.

This appliance is suitable for

installation in a bedroom or bed

sitting room.

The information contained in this manual is believed to

be correct at the time of printing. Miles Industries Ltd.

reserves the right to change or modify any information

or speci

cations without notice. Miles Industries Ltd.

grants no warranty, implied or stated, for the

installation or maintenance of your heater, and

assumes no responsibility for any consequential

damage(s).

Designed and manufactured for Miles Industries Ltd

Valor Fireplaces

190–2255 Dollarton Highway

North Vancouver, BC, Canada V7H 3B1

604.984.3496 F

604.984.0246

valor

replaces.com

This appliance may be installed in an

after-market permanently located,

manufactured (mobile) home where

not prohibited by local codes. This

appliance is only for use with the type

of gas indicated on the rating plate.

This appliance is not convertible for

use with other gases, unless a certi

kit is used.

INSTALLER: Leave this manual with the

appliance.
CONSUMER: Retain this manual for

future reference.

Massachusetts:

The piping and

nal gas connection must be

performed by a licensed plumber or gas

tter in

the State of Massachusetts. Also, see Carbon

Monoxide Detector requirements in this manual.

WARNING

This product can expose you to chemicals

including Benzene, which is known to the State

of California to cause cancer and birth defects or

other reproductive harm. For more information

go to www.P65Warnings.ca.gov.

Note: Natural gas, in its original state, contains

Benzene.

Summary of Contents for RetroFire RF24JDN


















































Search results

Summary of Contents for RetroFire RF24JDN

Reviews:

Brands by name

Popular brands

Valor RetroFire RF24JDN, Installation Manual

Search results

Summary of Contents for RetroFire RF24JDN

Reviews:

Brands by name

Popular brands