Valor RetroFire RF24JDN Installation Manual Download Page 17

Page: 17 / 49

Co-Axial with RA24CA

Typical Vent Installation

See

Approved Venting Components

on page 40 of this

manual.

Vent Location

The vent terminal must be located throught the roof.

This direct vent appliance is designed to operate when

an undisturbed air

ow hits the outside vent terminal

from any direction.
Check local codes for allowable vertical vent

termination.

Venting Table

Maximum

vertical height

40 ft (measured to bottom of termination)

Minimum

vertical height

8 ft (measured to bottom of termination

Maximum

horizontal run

4 ft (measured center to center of pipe

Maximum

ﬀ

set angle

45° (sweeping bend to allow for obstructions)

Venting Notes

Where possible, avoid splicing

ex pipes.

Four feet horizontal is permissible to allow for routing

around masonry projections. Do not bend

ex pipe

over a 45 degrees radius.
• Flex liners may only be installed into solid-fule burn-

ing

replaces and chimney systems (no combustible

constructions).

• The appliance must not be connected to a chimney

ue serving a separate solid-fuel burning appliance.

Terminal Cap (co-axial)

Co-axial applications (using RA24CA Vent Plate)

Terminal Adapter with

Flashing included in

590FVK2

RF24J

5 x 3” flex liners—

see Venting Table

for length allowed

5 x 3” Liners

5” min.
Bend
Radius

NOTE

Co-linear or co-axial flexible aluminum venting

liners should be professionally inspected

periodically for corrosion and damage and

replaced when necessary. If the installation does

not allow for future inspection or replacement of

the flexible aluminum liners, then stainless steel

vent liners are recommended.

Summary of Contents for RetroFire RF24JDN


















































Search results

Summary of Contents for RetroFire RF24JDN

Reviews:

Brands by name

Popular brands

Valor RetroFire RF24JDN, Installation Manual

Search results

Summary of Contents for RetroFire RF24JDN

Reviews:

Brands by name

Popular brands