Vallox MyVallox Control Manual Download Page 8

Page: 8 / 28

STARTING UP AND SHUTTING DOWN

THE UNIT

Unit software

We recommend that the latest software version be always used.
Check and download the latest version at http://www.cloud.vallox.
com either before or immediately after setup.
The current software version of the ventilation unit is shown on

the control panel display when the unit is connected to the mains

or factory settings are restored. Alternatively, the current software

version can be checked from the

Unit information

display of the

Service menu.

Updating the unit software

1. Unplug the ventilation unit from the mains or turn off the

fuse.

2. Connect the computer to the control panel of the

ventilation unit using a USB MicroB connector.

3. Start the ventilation unit. A USB sign will appear on the

display of the control panel and the control panel of the

ventilation unit cannot be used when it is connected to

the computer.

4. Transfer the update file you have downloaded onto

the ventilation unit. Copy the update file HSWUPD.

BIN (Please note! Do not alter the file name!) you have

downloaded at the root of the control panel (the control

panel will be displayed on your computer as a mass

memory or a removable disk drive). When the file has

uploaded onto the control panel, remove the USB

cable. Next, the control panel will take a while to load

the update. The control panel will now start to load the

update file onto the motherboard. This can take several

hours. The control panel will remain turned on, but it is

recommended that the control panel be not used during

that time. When the update is ready, the unit will restart

automatically.

Starting the unit

If you are starting the ventilation unit for the first time or after a

maintenance procedure, first connect it to the mains. This will start

the unit.
If the ventilation unit was turned off from the control panel (see

Turning the unit off), you can start it by pressing any control panel

button.

Turning the unit off

To turn the ventilation unit off:

1. Use the arrow buttons to select

Turn unit off

2. Select

3. Press

to confirm the selection. The ventilation unit has

now been turned off.

INTRODUCTION

IMPORTANT

It is recommended

that the ventilation be

kept turned on without

disruptions.

Summary of Contents for MyVallox Control





























Search results

Summary of Contents for MyVallox Control

Reviews:

Related manuals for MyVallox Control

Brands by name

Popular brands

Vallox MyVallox Control, Manual

Search results

Summary of Contents for MyVallox Control

Reviews:

Related manuals for MyVallox Control

Brands by name

Popular brands