Vallox MyVallox Control Manual Download Page 14

Page: 14 / 28

VENTILATION MODE SETTINGS

NOTE

By default, the fan speed used in the At home mode is the

higher of the percentage values set for basic ventilation airflows.

We recommend that this basic ventilation setting be used with

the At home mode. Once you have set the fan speed for the At

home mode, the fan speed for the Away mode will by default be

set to -30% of the At home mode fan speed. We recommend that

the default fan speed settings be used. However, the settings

can be changed as required.

At home and Away modes

To set the ventilation settings of the modes:

1. Use the

Plus

Minus

buttons to set the mode fan speed as

a percentage of the maximum output ratio.

2. The fan speed is now set for the mode.

3. Proceed to the next phase by selecting

Right arrow

4. Use the

Plus

Minus

buttons to set the desired supply air

temperature for the mode. You can adjust the temperature

setting in the range +5°C ... +25°C.

5. The supply air temperature of the mode is now set.

6. Proceed to the next phase by selecting

Right arrow

7. Use the

Arrow

buttons to turn the automatic fan speed

control based on relative humidity of air on or off.

8. The automatic fan speed control, based on the relative

humidity of air, is now set.

9. Proceed to the next phase by selecting

Right arrow

10. Use the

Arrow

buttons to turn the automatic fan speed

control based on carbon dioxide or VOC level on or off.

11. The automatic fan speed control, based on the carbon

dioxide or VOC level, is now set.

12. Select

13. Move to the settings of the next mode by selecting

NOTE

Once you have set the fan speed for the At home mode, the fan

speed for the Boost mode will by default be set to +30% of the

At home mode fan speed. It is recommended that this fan speed

setting be used for the Boost mode. However, the setting can be

changed as required.

Boost mode

The fan speed, supply air temperature, and the automatic fan speed

control (based on relative humidity of air or carbon dioxide or VOC

level) is set for the Boost mode in the same way as for the At home and

Away modes. The Boost mode also has a timer setting.

1. Use the

Arrow

buttons to select whether the mode timer

function is used or not. The options are:

TIP

You can browse the At

home mode settings

with the

Right arrow

button.

SETUP

Summary of Contents for MyVallox Control





























Search results

Summary of Contents for MyVallox Control

Reviews:

Related manuals for MyVallox Control

Brands by name

Popular brands

Vallox MyVallox Control, Manual

Search results

Summary of Contents for MyVallox Control

Reviews:

Related manuals for MyVallox Control

Brands by name

Popular brands