Vallox MyVallox Control Manual Download Page 5

Page: 5 / 28

VENTILATION UNIT CONTROL

Ventilation unit control options.

Operation of the Vallox ventilation unit can be controlled by the

following means:

• Through the control panel installed in the building

• Through the MyVallox Home local area network connection

and the MyVallox Home/Cloud user interface.

• Through the MyVallox Cloud service and the MyVallox

Home/Cloud user interface.

• Through a remote monitoring service or building

automation that uses voltage signals or Modbus messages

In addition to the integrated carbon dioxide and humidity

sensors, ventilation can also be adjusted automatically by using

the optional external carbon dioxide, VOC and humidity sensors.

When these are used, ventilation remains optimal even when the

dwelling is unoccupied.
Each user can use the week clock to adjust the ventilation to fit

their individual lifestyle.

SYSTEM DESCRIPTION

1. Internet

2. WLAN

3. Router

4. WLAN/LAN

5. Additional switch

6. Sensors

INTRODUCTION

NOTE

For the MyVallox Cloud/

Home instructions,

please go to www.

techmanuals.info/

ValloxMV/ENG/

onlinehelp/webhelp

MyVallox Cloud

MyVallox Home

Vallox MV

MyVallox Control

Modbus

KNX

KNX bus

module

Summary of Contents for MyVallox Control





























Search results

Summary of Contents for MyVallox Control

Reviews:

Related manuals for MyVallox Control

Brands by name

Popular brands

Vallox MyVallox Control, Manual

Search results

Summary of Contents for MyVallox Control

Reviews:

Related manuals for MyVallox Control

Brands by name

Popular brands