Valleylab LigaSure Service Manual Download Page 30

Page: 30 / 168

Rear Panel

Controls, Indicators,

and

Recept

acles

LigaSure Vessel Sealing Generator Service Manual

Vessel Sealing Footswitch Receptacle (purple)

Connect either the two-pedal vessel sealing footswitch or the single-pedal vessel
sealing footswitch to this receptacle.

Figure 3-7.

Vessel sealing footswitch
receptacle (purple)

Two Pedal Footswitch

The connected footswitch activates

either

vessel sealing or

bipolar output for the LigaSure instrument that is connected to
the Vessel Sealing Handset receptacle on the front panel.

Single Pedal Footswitch

The connected footswitch activates

only

the vessel sealing

output for the LigaSure instrument that is connected to the
Vessel Sealing Handset receptacle on the front panel

Bipolar Footswitch Receptacle (blue)

Figure 3-8.

Bipolar footswitch receptacle
(blue)

Connect the bipolar/macrobipolar footswitch when you
connect a bipolar footswitching instrument to the generator.

Connect the two-pedal bipolar footswitch to this receptacle.

The connected footswitch activates bipolar or macrobipolar output for the bipolar
instrument that is connected to the Bipolar handset receptacle on the front panel.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for LigaSure









































































































































































Search results

Summary of Contents for LigaSure

Reviews:

Valleylab LigaSure, Service Manual, Page: 30 / 168

Search results

Summary of Contents for LigaSure

Reviews: