manualshive.com logo in svg

Valleylab LigaSure, Service Manual, Page: 125 / 168

Share
Download
Valleylab LigaSure Service Manual Download Page 125

High Voltage (HV) Power Supply Board

8-6

LigaSure Vessel Sealing Generator Service Manual

4.

Remove four cables from the HV power supply board:

*All reference points in this table appear on the HV power supply board.

Two latches secure the ribbon cable connector to the HV power supply board. 
Release them by rotating them away from the connector, then pull the 
connector away from the board.

5.

Remove three screws (M4 x.7 x 8) that secure the HV power supply board to 

the chassis.

Note that the screw nearest the rear of the unit also fastens the chassis ground 
to the board by way of a ring tongue terminal.

6.

Lift the HV power supply board out of the chassis.

Figure 8-3.                                                             

Heat sink bracket and cable 
connections on the HV power 
supply board

Name

Ref*

Location

Wires

Colors

Switched AC 
power cable

J2

upper rear corner 
of the board

3

brown, blue, and 
green/yellow

AC switch #1 
cable

J1

next to the first 
cable

2

brown and blue

HV power 
supply control 
ribbon cable

J3

near the front 
edge of the board

ribbon

red and gray

HV DC cable 

J4

under the HV 
power supply 
control ribbon 
cable

 4

two black and two 
red

Switched AC 
Power Cable

AC Switch 
Cable

Heat Sink Bracket

HV Power Supply Control 
Ribbon Cable

HV DC Cable

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for LigaSure









































































































































































Reviews:

No comments