manualshive.com logo in svg

Valleylab LigaSure, Service Manual, Page: 111 / 168

Share
Download
Valleylab LigaSure Service Manual Download Page 111

Responding to System Alarms

7-14

LigaSure Vessel Sealing Generator Service Manual

108

CORRECTED_RTC_CRC_DATA
Real time clock RAM CRC test failed 
during initialization, but the data was 
restored from battery backed RAM.

Reported to serial port only. 

Replace the battery.

If the error code reappears, replace the control board (failed 
U1).

109

CORRECTED_BATRAM_CRC_DATA
Real time clock RAM CRC test failed 
during initialization. An attempt to correct 
the problem failed.

Replace the battery.

If the error code reappears, replace the control board. 

110

111

112

113

114

INVALID_RECENT_ERRORS
Recent error data kept in battery backed 
RAM was found to have an invalid CRC 
at powerup.

INVALID_ERROR_COUNTS
Error counts kept in battery backed RAM 
was found to have an invalid CRC at 
powerup.

INVALID_LAST_POWER_SETTINGS
Last power settings structure in battery 
backed RAM was found to have an 
invalid CRC at powerup.

INVALID_STATS_COUNTS
Statistical data kept in battery backed 
RAM was found to have an invalid CRC 
at powerup

INVALID_MINUTES_ON_WARNING
Minutes On data kept in battery backed 
RAM was found to have an invalid CRC 
at powerup.

Reported to serial port only. 

Replace the battery.

If the error code reappears, replace the control board.

115

MM_DOSERR_TEST_ERROR
Master microprocessor reported a 
powerup DOSERR test failure.

Turn the power switch off (O) then on again (|).

If the error reappears, replace the control board.

If the error reappears, replace high voltage power supply.

If the error reappears, replace RF output FET Q5 on the RF 
board.

116

DOSERR_TEST_MEMORY_FAULT
Doserror test state variable corrupted 
during powerup dose error test.

Turn the power switch off (O) then on again (|).

If the error reappears, replace the control board.

117

MICRO_COMPATIBILITY_ERROR
Incompatible software versions on 
feedback and master processors, or 
master side software incompatible with 
digital board type.

Turn the power switch off (O) then on again (|).

If the error reappears, replace the control board.

118

DPRAM_RENDEZVOUS_ERROR
Master and feedback processors fail to 
communicate on power up. Either timing 
or content of communication invalid.

Turn the power switch off (O) then on again (|).

If the error reappears, replace the control board.

Number

Description

Recommended Action

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for LigaSure









































































































































































Reviews:

No comments