Vacon NX ACTIVE FRONT END II Applications Manual Download | Manualshive

Page: 74 / 94

background image

74

• Vacon

arfiff05 Standard AFE-II

Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/

B00: FALSE = Open MCB, TRUE = PreCharge DC
Open MCB: Opens MCB if closed, stops precharging if charging is active trough the drive.
PreCharge DC: Drive will start precharge if function activated by digital output and control place is
fieldbus. When control place is not fieldbus precharging is started from normal start command.

B01: MCB Close Enable

FALSE: MCB Closing is disabled in fieldbus control. MCB Remains open when if DC voltage is above
closing limit.
TRUE: MCB Closing is enabled in fieldbus control. This bit can be true all the time if function is not
needed.

B02: Quick Stop

FALSE: Drive will stop modulation immediately and open MCB immediately.
TRUE: Quick stop is not active and normal operation is possible.

B03: FALSE = Stop Request, TRUE = Start Request
Stop Request: Drive will stop .
Start Request: Start Command to the drive. Rising edge needed for start.

B04: Output Power Limit to Zero
FALSE: Output power limit is reduced to 7 % if parameter limit is higher.
TRUE: Power limit is defined by power limit parameters.

B05: Disable Power Increase. Input or Output
FALSE:

TRUE: Power limit is defined by power limit parameters.

B06: Input Power Limit to Zero
FALSE: Input power limit is reduced to 7 % if parameter limit is higher
TRUE: Power limit is defined by power limit parameters.

B07: FALSE = No significance, TRUE = Fault Acknowledge

Fault Acknowledge: The group signal is acknowledged with a positive edge.

B08: FALSE = No Function, TRUE = DC Ref 1

B09: FALSE = No Function, TRUE = DC Ref 2

B10: FALSE = FB Control disabled TRUE = FB Control Enabled

FB Control Disabled: Drive will not follow main control word from Fieldbus. If removed while
running drive will make coasting stop.
FB Control Enabled: Drive follows control word from fieldbus

B11: FALSE = FB WD Pulse Low, TRUE = FB WD Pulse High

Watch dog pulse: This pulse is used to monitor that PLC is alive. If pulse is missing drive will go to
fault state. This function is activated by P2.7.6 FB WD Delay. When value is zero pulse si not
monitored.

DC Ref

FB Reference

110,00 %

115,00 %

120,00 %

B08

FALSE

TRUE

FALSE

TRUE

B09

FALSE

FALSE

TRUE

TRUE

«
...
72
73
74
75
76
...
»

Summary of Contents for NX ACTIVE FRONT END II































































































Reviews:

No comments

Related manuals for NX ACTIVE FRONT END II

Brand: IBM Pages: 144

Brand: Gatekeeper Pages: 28

Brand: V2 ELETTRONICA Pages: 72

Brand: M-system Pages: 103

Brand: M-system Pages: 18

Brand: M-system Pages: 7

Brand: Mamas & Papas Pages: 44

Brand: Mamas & Papas Pages: 8

Brand: Omegalink Pages: 2

Brand: MamaLove Pages: 9

Brand: Uniden Pages: 28

Brand: UniFocus Pages: 23

Brand: UniFocus Pages: 6

IntelliZone2 MasterStat

Brand: Water Furnace Pages: 44

Brand: DigiPower Pages: 27

Brand: oventrop Pages: 64

Brand: WEST Pages: 2

Brand: CLIMAVENETA Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands